Combined Cycle Power Plant Fundamentals Course

Name: Combined Cycle Power Plant Fundamentals Training Course
Availability: InStock

Build a practical plant-wide view of gas turbine, HRSG, steam cycle, auxiliaries, operating limits, and performance.

Combined Cycle Power Plant Fundamentals Course

At a glance

Duration: 1 Week
Format: Classroom
Cities: Baku, Trabzon, Tokyo, Tbilisi, Accra, Frankfurt and more
Next session: 26 – 30 October 2026, Baku
Average fee: 7,500 €

Home
Our Categories
Combined Cycle Power Plant Fundamentals Training Course

Overview

Combined Cycle Power Plant Fundamentals Training Course is a one-week foundation course for operators, maintenance technicians, junior engineers, utility staff, and new generation professionals who leave with a Combined Cycle Operating Map. Participants trace combined cycle power plant fundamentals through the gas turbine, heat recovery steam generator, steam turbine, condenser, and balance of plant, linking thermodynamics with safe sequences, performance, emissions, and coordinated troubleshooting. Agile Leaders Training Center provides foundation learning in combined-cycle plant operation.

Who Should Attend

Personnel responsible for monitoring plant status, alarms, limits, and operating sequences
Teams responsible for maintaining turbines, heat-recovery equipment, auxiliaries, and electrical interfaces
Engineers responsible for reviewing process behavior, efficiency, output, and equipment condition
Utility staff responsible for coordinating generation availability and operating requirements
Professionals preparing to work with combined-cycle generation assets

The course assumes participants can read basic process information and follow site safety procedures; it leaves out detailed equipment design, control-system programming, and specialist overhaul work.

Departments and Industries

The course supports departments that operate, maintain, and coordinate thermal generation assets.

Power generation operations and maintenance
Utility engineering and dispatch coordination
Industrial energy and cogeneration facilities
Oil, gas, petrochemical, and process utilities
Technical services, reliability, and performance teams

Learning Objectives

By the end of this course, participants will be able to:

Apply combined-cycle process and thermodynamic vocabulary
Analyze gas-turbine, HRSG, steam-cycle, and auxiliary interactions
Use start-up and shutdown sequence maps
Evaluate heat rate, output, emissions, and ambient effects
Diagnose alarms through operating limits and causal evidence
Build a coordinated troubleshooting and safety response map

Course Agenda

Day 1: Plant Configuration and Energy Flow

Combined-Cycle Topping and Bottoming Cycle Diagram
Brayton and Rankine Cycle Relationship Map
Gas-to-Electricity Energy Balance Worksheet
Plant Equipment Boundary and Interface Matrix
Process Measurement and Operating Variable Register

Day 2: Gas Turbine and Heat Recovery

Gas Turbine Compressor-Combustor-Expander Flow Map
Combustion Temperature and Emissions Control Logic
HRSG Pressure-Level and Heat-Recovery Diagram
Drum, Economizer, Evaporator, and Superheater Function Matrix
Exhaust Temperature and Pinch-Point Performance Screen

Day 3: Steam Cycle and Balance of Plant

Steam Turbine Expansion and Extraction Pathway
Condenser Vacuum and Cooling-System Cause Map
Water-Steam Chemistry Interface Checklist
Feedwater, Condensate, and Pump System Flow Diagram
Electrical, Fuel, Air, and Auxiliary System Interface Register

Day 4: Operating Sequences, Performance, and Safety

Cold, Warm, and Hot Start Sequence Map
Normal Shutdown and Trip Response Decision Tree
Heat Rate, Output, and Ambient Correction Worksheet
Operating Limit, Alarm, and Interlock Response Matrix
Energy Isolation and Process Hazard Review Checklist

Day 5: Integrated Practice and Troubleshooting

Exercise on Combined-Cycle Energy Flow Reconstruction
Exercise on Gas Turbine and HRSG Deviation Analysis
Exercise on Steam-Cycle and Condenser Fault Isolation
Exercise on Start-up Alarm and Performance Prioritization
Capstone Exercise: Combined Cycle Operating Map

Practical Exercises

The course uses suggested activities that connect plant indications with operating decisions.

Suggested activity: trace energy and mass flow through a plant configuration diagram
Suggested activity: interpret an alarm set using limits, interlocks, and process dependencies
Suggested activity: compare heat-rate changes against load, ambient conditions, and equipment state
Suggested activity: build a coordinated response map for an integrated plant deviation

FAQs

Who suits combined cycle power plant fundamentals training, and what does it assume?

Operators, technicians, junior engineers, utility staff, and new generation professionals suit the course. It assumes basic process-reading ability and familiarity with workplace safety procedures, without requiring prior combined-cycle specialization.

How does combined cycle power plant fundamentals differ from gas turbine maintenance training?

Combined-cycle fundamentals connect the gas turbine with the HRSG, steam turbine, condenser, auxiliaries, operating sequences, and performance. Gas turbine maintenance training concentrates more deeply on inspection, servicing, and repair of the gas-turbine package.

How does a combined cycle power plant generate more electricity from fuel?

A combined-cycle plant uses a gas turbine to generate power, then recovers hot exhaust energy in an HRSG to produce steam for a steam turbine. The second cycle converts heat that would otherwise leave with the exhaust.

What affects combined cycle plant heat rate and output?

Load, ambient temperature, compressor condition, firing conditions, HRSG heat transfer, steam conditions, condenser pressure, auxiliary consumption, and operating configuration affect heat rate and output. Trends require consistent boundaries and corrected comparisons.

Why are start-up limits important in combined cycle plant operation?

Start-up limits manage thermal stress, pressure, temperature, chemistry, emissions, and equipment permissives while gas and steam systems come online. Sequence discipline helps personnel identify abnormal conditions before they propagate across connected equipment.

Conclusion

Participants leave with a Combined Cycle Operating Map linking equipment functions, energy flows, sequences, limits, performance indicators, safety controls, and troubleshooting evidence. The map changes isolated readings into a structured view of plant behavior. Teams can reuse it to coordinate monitoring, escalation, and first-line diagnosis before specialist intervention.

credits: 5 credit per day

Course Mode: full-time

Provider: Agile Leaders Training Center

Download Brochure (PDF) Print PDF

Showing 21-40 of 57 events

Location	Dates	Duration	Mode	Price
Lisbon	Week 07, 2027 15 – 19 February 2027	1 Week	Onsite	€6,500
Kuwait	Week 07, 2027 21 – 25 February 2027	1 Week	Onsite	€7,000
Kuala Lumpur	Week 08, 2027 22 – 26 February 2027	1 Week	Onsite	€6,500
Vienna	Week 09, 2027 1 – 5 March 2027	1 Week	Onsite	€7,500
Amman	Week 09, 2027 7 – 11 March 2027	1 Week	Onsite	€6,000
Milan	Week 12, 2027 22 – 26 March 2027	1 Week	Onsite	€7,000
Dubai	Week 13, 2027 29 March – 2 April 2027	1 Week	Onsite	€6,500
Sharm El-Sheikh	Week 14, 2027 5 – 9 April 2027	1 Week	Onsite	€5,200
Zanzibar	Week 14, 2027 11 – 15 April 2027	1 Week	Onsite	€6,000
Rome	Week 18, 2027 3 – 7 May 2027	1 Week	Onsite	€6,500
Nice	Week 18, 2027 3 – 7 May 2027	1 Week	Onsite	€8,000
Abu Dhabi	Week 19, 2027 10 – 14 May 2027	1 Week	Onsite	€6,500
Marbella	Week 19, 2027 16 – 20 May 2027	1 Week	Onsite	€6,500
Zoom	Week 20, 2027 17 – 21 May 2027	1 Week	Online	€3,000
Manama	Week 20, 2027 23 – 27 May 2027	1 Week	Onsite	€6,500
Amsterdam	Week 22, 2027 31 May – 4 June 2027	1 Week	Onsite	€6,500
Dubai	Week 23, 2027 7 – 11 June 2027	1 Week	Onsite	€6,500
Singapore	Week 23, 2027 7 – 11 June 2027	1 Week	Onsite	€6,500
Athens	Week 25, 2027 21 – 25 June 2027	1 Week	Onsite	€7,500
Abu Dhabi	Week 28, 2027 12 – 16 July 2027	1 Week	Onsite	€6,500

Frequently asked questions

What does this course cover?

OverviewCombined Cycle Power Plant Fundamentals Training Course is a one-week foundation course for operators, maintenance technicians, junior engineers, utility staff, and new generation professionals who leave with a Combined Cycle Operating Map. Participants trace combined cycle power plant fundamentals through the gas turbine, heat recovery steam gene…

Are training dates available?

Yes. Available dates and destinations are listed in the course dates section on this page.

How can I register?

Choose an available date on this page and complete the registration form, or send a programme enquiry.

Can I download the course brochure?

Yes. Use the brochure download link provided on this page.

Combined Cycle Power Plant Fundamentals Course