Circuit Breaker Timing and Motion Analysis Course

Name: Circuit Breaker Timing and Motion Analysis Course
Availability: InStock

Configure breaker timing and motion tests, validate traces, and diagnose mechanical condition from travel and velocity evidence.

At a glance

Duration: 1 Week
Format: Classroom
Cities: Porto, Prague, Berlin, Lagos, Madrid, Dubai and more
Next session: 26 – 30 October 2026, Porto
Average fee: 7,500 €

Home
Our Categories
Circuit Breaker Timing and Motion Analysis Course

Download Brochure (PDF) Print PDF

Overview

Circuit Breaker Timing and Motion Analysis Course is a one-week advanced course for electrical maintenance engineers, protection technicians, commissioning engineers, and switchgear test specialists who need a repeatable Breaker Motion Diagnostic File. Participants learn to configure timing channels and motion transducers, capture operating sequences, calculate travel and velocity indicators, judge trace quality, and relate deviations to mechanical condition. The course concentrates on measurement evidence rather than general switchgear maintenance. Agile Leaders Training Center delivers focused circuit breaker timing and motion analysis training.

Who Should Attend

Teams responsible for condition testing of medium- and high-voltage circuit breakers
Personnel who commission protection and primary plant interfaces
Maintenance specialists who investigate slow, unequal, or unstable breaker operation
Test engineers who configure timing analyzers and travel transducers
Technical supervisors who review breaker test evidence and return-to-service decisions

The course assumes participants already work safely around isolated switchgear and can read breaker control diagrams; it leaves out protection-relay grading and general switchgear overhaul.

Departments and Industries

The course supports departments that verify circuit breaker mechanical performance from measured evidence.

Power generation electrical maintenance and outage teams
Transmission and distribution substation testing groups
Oil, gas, petrochemical, and process-plant reliability functions
Industrial manufacturing electrical services
EPC commissioning and specialist testing contractors

Learning Objectives

By the end of this course, participants will be able to:

Apply safe test preparation and connection controls
Use timing analyzers and linear or rotary transducers
Build repeatable open, close, and operating-sequence test plans
Analyze timing, travel, velocity, overtravel, rebound, and wipe
Diagnose mechanical defects from synchronized traces
Compare results with manufacturer limits and previous records

Course Agenda

Day 1: Test Strategy, Safety, and Breaker Mechanics

Circuit Breaker Timing Test Purpose and Evidence Map
Operating Mechanism, Linkage, Main Contact, and Auxiliary Contact Model
Safe Isolation, Grounding, Stored-Energy, and Control-Supply Checklist
Nameplate, Drawing, Manual, and Baseline Data Review
Breaker Timing and Motion Test Plan Exercise

Day 2: Timing Channels and Operating Sequences

Main, Resistor, and Auxiliary Contact Channel Assignment
Open, Close, Close-Open, and Open-Close Sequence Configuration
Operating Time, Pole Discrepancy, Dead Time, and Dwell Time Worksheet
Trip Coil, Close Coil, Control Voltage, and Trigger Alignment
Circuit Breaker Timing Analyzer Setup Practice

Day 3: Contact Travel and Velocity Measurement

Linear and Rotary Motion Transducer Selection Matrix
Transducer Mounting, Direction, Scaling, and Zero Reference
Stroke, Contact Wipe, Overtravel, and Rebound Calculation Sheet
Average and Instantaneous Velocity Window Selection
Circuit Breaker Travel and Velocity Testing Trace Review

Day 4: Trace Quality and Mechanical Diagnosis

Noise, Bounce, Lost Motion, Saturation, and Trigger Error Checks
Slow Operation, Pole Scatter, Damping, and Linkage Defect Patterns
Coil Current and Motion Trace Correlation Method
First-Trip and In-Service Timing Evidence Discussion
Advanced Circuit Breaker Timing Diagnostics Case File

Day 5: Acceptance, Trending, and Capstone

Manufacturer Limit, Commissioning Baseline, and Trend Comparison
Repeatability, Uncertainty, and Retest Decision Record
Exception Classification and Maintenance Recommendation Table
Test Report, Trace Annotation, and Technical Handover
Capstone Exercise: Breaker Motion Diagnostic File

Practical Exercises

The course uses structured exercises that turn analyzer traces into defensible maintenance evidence.

Suggested activity: prepare a safe connection and channel map from a breaker schematic
Suggested activity: calculate timing spread, travel, velocity, overtravel, rebound, and wipe
Suggested activity: distinguish a mechanical defect from poor transducer setup or trigger error
Suggested activity: produce a recommendation from baseline, current, and repeated measurements

FAQs

What does circuit breaker timing and motion analysis measure?

It records when main and auxiliary contacts change state and how the moving mechanism travels during operation. The resulting synchronized traces support calculations for operating time, pole discrepancy, stroke, wipe, overtravel, rebound, and velocity.

How is this different from general switchgear maintenance training?

This course is limited to circuit breaker timing, travel, velocity, trace validation, mechanical diagnosis, and evidence-based reporting. It does not teach the wider inspection, servicing, insulation, protection, and overhaul scope of a general switchgear course.

Which operating sequences are examined?

Participants examine open, close, close-open, and open-close sequences where applicable. The exact sequence and test limits must follow the breaker design, operating instructions, site procedure, and approved test plan.

Why does transducer setup matter in breaker motion testing?

Mounting position, direction, conversion ratio, zero reference, free movement, and sampling configuration directly affect the travel curve. An incorrect setup can resemble a real mechanical defect, so trace-quality checks precede diagnosis.

How should test results be judged?

Results should be compared with manufacturer limits, commissioning baselines, previous measurements, operating conditions, and repeat tests. A single generic limit is not suitable for every breaker mechanism or transducer position.

Conclusion

Participants leave with a Breaker Motion Diagnostic File containing a test plan, connection map, sequence records, timing and travel calculations, trace-quality checks, defect interpretations, trend comparisons, and a technical recommendation. The file provides a repeatable route from field measurement to review and maintenance action.

credits: 5 credit per day

Course Mode: full-time

Provider: Agile Leaders Training Center

Download Brochure (PDF) Print PDF

Showing 1-20 of 57 events

Location	Dates	Duration	Mode	Price
Porto	Week 44, 2026 26 – 30 October 2026	1 Week	Onsite	€6,500
Prague	Week 45, 2026 2 – 6 November 2026	1 Week	Onsite	€7,500
Berlin	Week 45, 2026 2 – 6 November 2026	1 Week	Onsite	€6,500
Lagos	Week 46, 2026 15 – 19 November 2026	1 Week	Onsite	€6,000
Madrid	Week 48, 2026 23 – 27 November 2026	1 Week	Onsite	€6,500
Dubai	Week 49, 2026 30 November – 4 December 2026	1 Week	Onsite	€6,500
San Diego	Week 49, 2026 30 November – 4 December 2026	1 Week	Onsite	€16,000
Chicago	Week 49, 2026 6 – 10 December 2026	1 Week	Onsite	€16,000
Paris	Week 50, 2026 7 – 11 December 2026	1 Week	Onsite	€6,500
Sharm El-Sheikh	Week 51, 2026 14 – 18 December 2026	1 Week	Onsite	€5,200
Cape town	Week 51, 2026 20 – 24 December 2026	1 Week	Onsite	€6,000
Zoom	Week 52, 2026 21 – 25 December 2026	1 Week	Online	€3,000
Milan	Week 01, 2027 4 – 8 January 2027	1 Week	Onsite	€7,000
Geneva	Week 01, 2027 10 – 14 January 2027	1 Week	Onsite	€8,000
Seoul	Week 02, 2027 11 – 15 January 2027	1 Week	Onsite	€12,000
Vienna	Week 03, 2027 18 – 22 January 2027	1 Week	Onsite	€7,500
London	Week 04, 2027 25 – 29 January 2027	1 Week	Onsite	€6,500
Langkawi	Week 05, 2027 7 – 11 February 2027	1 Week	Onsite	€8,000
Athens	Week 08, 2027 22 – 26 February 2027	1 Week	Onsite	€7,500
Zanzibar	Week 08, 2027 28 February – 4 March 2027	1 Week	Onsite	€6,000

Frequently asked questions

What does this course cover?

OverviewCircuit Breaker Timing and Motion Analysis Course is a one-week advanced course for electrical maintenance engineers, protection technicians, commissioning engineers, and switchgear test specialists who need a repeatable Breaker Motion Diagnostic File. Participants learn to configure timing channels and motion transducers, capture operating sequen…

Are training dates available?

Yes. Available dates and destinations are listed in the course dates section on this page.

How can I register?

Choose an available date on this page and complete the registration form, or send a programme enquiry.

Can I download the course brochure?

Yes. Use the brochure download link provided on this page.

Circuit Breaker Timing and Motion Analysis Course