Control Valves and Actuators Training Course

Name: Control Valves and Actuators Foundation Course
Availability: InStock

Select, inspect, calibrate and diagnose industrial control valves, actuators and positioners using structured evidence.

Control Valves and Actuators Training Course

At a glance

Duration: 1 Week
Format: Classroom
Cities: Jakarta, Manama, Cairo, Amman, Lagos, Kuala Lumpur and more
Next session: 9 – 13 November 2026, Jakarta
Average fee: 7,500 €

Home
Our Categories
Control Valves and Actuators Foundation Course

Overview

Control Valves and Actuators Foundation Course is a one-week programme for instrumentation, control, maintenance and commissioning personnel who leave with a Control Valve Inspection and Commissioning Workbook. Participants examine valve bodies, trim, flow characteristics, sizing inputs, service damage, actuator types, positioners, fail action, calibration, stroke testing and diagnostics. Activities use approved data and isolated equipment rather than live process intervention. Agile Leaders Training Center presents control valves and actuators through structured equipment decisions.

Who Should Attend

Personnel responsible for control-valve inspection, calibration and repair
Engineers selecting valve, actuator and positioner arrangements
Operators identifying valve-response and process symptoms
Reliability teams analysing recurring valve and actuator faults
Commissioning personnel verifying installation, stroking and records

The course assumes participants can read basic piping and instrumentation diagrams and instrument signals, and it leaves out detailed piping design, advanced loop tuning, live process work and manufacturer-specific overhaul authorization.

Departments and Industries

The course supports departments and industries that depend on modulating valves for reliable process control.

Oil, gas, refining and petrochemical operations
Power generation, water and utility systems
Chemical, pharmaceutical and food processing
Instrumentation, control and automation departments
Maintenance, reliability, operations and commissioning teams

Learning Objectives

By the end of this course, participants will be able to:

Analyze valve bodies, trim and service conditions
Apply flow-characteristic and sizing concepts to selection checks
Compare pneumatic, electric and hydraulic actuator arrangements
Use calibration and stroke-test evidence to assess performance
Diagnose common valve, actuator and positioner faults
Build controlled maintenance and commissioning records

Course Agenda

Day 1: Valve Construction and Service Selection

Control Valve Function within the Process Loop
Globe, Ball, Butterfly and Plug Valve Comparison
Body, Bonnet, Stem, Seat, Plug and Trim Identification
Two-Port, Three-Port, Mixing and Diverting Applications
Control Valve Inspection and Commissioning Workbook Structure

Day 2: Flow Characteristics and Service Effects

Cv and Kv Flow-Capacity Concept
Linear, Equal-Percentage and Quick-Opening Characteristics
Rangeability, Pressure Drop and Installed Behaviour
Liquid, Gas and Steam Sizing Input Checks
Cavitation, Flashing, Noise and Erosion Indicators

Day 3: Actuators, Positioners and Fail Action

Pneumatic Diaphragm and Piston Actuator Operation
Electric and Hydraulic Actuator Application
Positioner, I/P Converter, Solenoid and Air-Set Interface
Air-to-Open, Air-to-Close and Fail-Position Decisions
Thrust, Torque, Travel and Seat-Load Checks

Day 4: Installation, Calibration and Diagnostics

Orientation, Supports, Bypass and Accessibility Review
Supply Pressure, Tubing and Electrical Connection Checks
Zero, Span, Travel and Positioner Calibration
Stroke Test, Step Response and Deadband Evidence
Leakage, Stiction, Hunting and Position-Deviation Diagnosis

Day 5: Maintenance and Commissioning Practice

Exercise: Identify Valve, Trim and Actuator Components
Exercise: Review Sizing Inputs and Service-Damage Risks
Exercise: Calibrate a Positioner and Record a Stroke Test
Exercise: Diagnose a Valve-Response Fault from Evidence
Capstone Exercise: Complete a Control Valve Inspection and Commissioning Workbook

Practical Exercises

The course uses suggested activities based on approved datasheets, isolated equipment and simulated diagnostic records.

Suggested activity: compare valve characteristics against a service requirement
Suggested activity: verify fail action and accessory connections from a schematic
Suggested activity: interpret travel, pressure and response data for a suspected fault
Suggested activity: prepare inspection, calibration and commissioning acceptance records

FAQs

Who is the course for and what does it assume?

It suits instrumentation, control, maintenance, operations and commissioning personnel. It assumes basic familiarity with P&IDs, instrument signals and safe isolation practices.

How does this differ from a PID loop-tuning course?

This course concentrates on valve bodies, trim, actuators, positioners, calibration and equipment diagnostics. A PID tuning course concentrates on controller response and loop-adjustment methods.

Does the course perform detailed control-valve sizing?

It teaches sizing inputs, capacity concepts and verification checks. Final sizing and selection require current process data, approved equations, manufacturer information and competent engineering review.

What is the difference between cavitation and flashing?

Both begin when liquid pressure falls to the vapour-pressure region. Cavitation involves bubble collapse after pressure recovery; flashing persists downstream when pressure does not recover sufficiently.

What practical output is completed?

Participants complete a Control Valve Inspection and Commissioning Workbook covering selection checks, components, fail action, calibration, diagnostics, maintenance and acceptance evidence.

Conclusion

Participants leave with a repeatable method for examining control-valve assemblies, confirming actuator action, interpreting performance evidence and documenting controlled work. The workbook connects service conditions, components, calibration and fault diagnosis while approved procedures, isolation controls and manufacturer limits remain in charge.

credits: 5 credit per day

Course Mode: full-time

Provider: Agile Leaders Training Center

Download Brochure (PDF) Print PDF

Showing 1-20 of 58 events

Location	Dates	Duration	Mode	Price
Jakarta	Week 46, 2026 9 – 13 November 2026	1 Week	Onsite	€8,000
Manama	Week 46, 2026 15 – 19 November 2026	1 Week	Onsite	€6,500
Cairo	Week 47, 2026 16 – 20 November 2026	1 Week	Onsite	€5,200
Amman	Week 47, 2026 22 – 26 November 2026	1 Week	Onsite	€6,000
Lagos	Week 48, 2026 29 November – 3 December 2026	1 Week	Onsite	€6,000
Kuala Lumpur	Week 50, 2026 7 – 11 December 2026	1 Week	Onsite	€6,500
Istanbul	Week 50, 2026 7 – 11 December 2026	1 Week	Onsite	€6,000
Abu Dhabi	Week 51, 2026 14 – 18 December 2026	1 Week	Onsite	€6,500
Addis Ababa	Week 52, 2026 21 – 25 December 2026	1 Week	Onsite	€6,000
Bali	Week 52, 2026 27 – 31 December 2026	1 Week	Onsite	€6,500
Barcelona	Week 01, 2027 4 – 8 January 2027	1 Week	Onsite	€6,500
Zoom	Week 02, 2027 11 – 15 January 2027	1 Week	Online	€3,000
Tbilisi	Week 03, 2027 18 – 22 January 2027	1 Week	Onsite	€5,700
Dubai	Week 04, 2027 25 – 29 January 2027	1 Week	Onsite	€6,500
Porto	Week 04, 2027 25 – 29 January 2027	1 Week	Onsite	€6,500
Kuwait	Week 04, 2027 31 January – 4 February 2027	1 Week	Onsite	€7,000
London	Week 05, 2027 1 – 5 February 2027	1 Week	Onsite	€6,500
Bangkok	Week 05, 2027 7 – 11 February 2027	1 Week	Onsite	€8,000
Vienna	Week 07, 2027 15 – 19 February 2027	1 Week	Onsite	€7,500
Chicago	Week 07, 2027 21 – 25 February 2027	1 Week	Onsite	€16,000

Frequently asked questions

What does this course cover?

OverviewControl Valves and Actuators Foundation Course is a one-week programme for instrumentation, control, maintenance and commissioning personnel who leave with a Control Valve Inspection and Commissioning Workbook. Participants examine valve bodies, trim, flow characteristics, sizing inputs, service damage, actuator types, positioners, fail action, ca…

Are training dates available?

Yes. Available dates and destinations are listed in the course dates section on this page.

How can I register?

Choose an available date on this page and complete the registration form, or send a programme enquiry.

Can I download the course brochure?

Yes. Use the brochure download link provided on this page.

Control Valves and Actuators Training Course