Dynamic Reservoir Simulation Training Course

Name: Dynamic Oil and Gas Reservoir Simulation Training Course
Availability: InStock

Construct, run, diagnose, and quality-check dynamic reservoir models for practical field-development forecasts.

Dynamic Reservoir Simulation Training Course

At a glance

Duration: 1 Week
Format: Classroom
Cities: Geneva, Abu Dhabi, London, Montreux, Vienna, Amman and more
Next session: 15 – 19 November 2026, Geneva
Average fee: 7,500 €

Home
Our Categories
Dynamic Oil and Gas Reservoir Simulation Training Course

Overview

Dynamic Oil and Gas Reservoir Simulation Training Course is a one-week intermediate course for reservoir, simulation, subsurface, production, petroleum-engineering, and asset functions who leave with a Reservoir Simulation Study File. Participants convert static earth models and engineering data into initialized dynamic models, represent wells and controls, manage numerical runs, diagnose results, perform foundational history matching, and compare development forecasts. The course emphasizes traceable inputs, stable execution, and decision-ready outputs. Agile Leaders Training Center presents practical dynamic reservoir simulation.

Who Should Attend

Reservoir-engineering functions responsible for dynamic models and production forecasts
Simulation functions responsible for model construction, execution, and result diagnosis
Subsurface-modeling functions responsible for grid, property, and uncertainty inputs
Production-technology functions responsible for well behavior and surveillance evidence
Petroleum-engineering functions responsible for recovery plans and development scenarios
Asset functions responsible for integrating technical forecasts into field decisions

The course assumes participants already use reservoir, well, fluid, and production data at work, and it leaves out introductory petroleum geology, software certification, advanced assisted history matching, and ensemble optimization.

Departments and Industries

The course supports departments and industries that construct, use, or assure dynamic subsurface forecasts.

Reservoir engineering, simulation, and subsurface modeling
Production technology, petroleum engineering, and well performance
Field development, asset planning, and technical assurance
Oil and gas exploration, development, and production
Underground gas storage and carbon-storage project teams
Energy consulting, engineering services, and applied research

Learning Objectives

By the end of this course, participants will be able to:

Build a simulation-ready grid and input register
Apply fluid, rock-flow, equilibrium, and aquifer data
Use well models, completions, schedules, and controls
Diagnose timestep, convergence, balance, and output issues
Compare historical response and development forecasts
Evaluate model quality, limitations, and decision evidence

Course Agenda

Day 1: Frame the Dynamic Model

Reservoir Simulation Purpose and Study-Scope Charter
Static-to-Dynamic Model Handover Checklist
Grid Geometry, Active Cells, and Upscaling Register
Porosity, Permeability, Regions, and Fault Representation
Units, Datum, Conventions, Assumptions, and Data Lineage

Day 2: Initialize Fluids and Rock Flow

Pressure-Volume-Temperature Data and Fluid Model Selection
Relative Permeability and Capillary Pressure Functions
Rock Compressibility and Pore-Volume Behavior
Initial Pressure, Saturation, Contacts, and Equilibration
Aquifer Selection, Boundary Conditions, and Volume Checks

Day 3: Represent Wells and Run Cases

Well Trajectory, Completion, Connection, and Skin Model
Production and Injection Controls with Operating Constraints
Historical Schedule, Events, and Restart Strategy
Timestep, Solver, Convergence, and Numerical-Control Review
Run Management, Messages, Material Balance, and Result Plots

Day 4: Calibrate and Forecast

Pressure, Rate, Water-Cut, and Gas-Oil-Ratio Comparison
Foundational History-Match Parameter and Evidence Register
Mismatch Diagnosis and Physically Plausible Adjustment Cycle
Base Case, Development Scenario, and Forecast Assumptions
Well, Field, Recovery, and Constraint Forecast Comparison

Day 5: Assure the Simulation Study

Suggested Exercise: Assemble a Simulation-Ready Input Register
Suggested Exercise: Initialize and Check a Dynamic Model
Suggested Exercise: Diagnose a Failed or Unstable Run
Suggested Exercise: Compare History and Forecast Responses
Capstone Exercise: Complete the Reservoir Simulation Study File

Practical Exercises

The course uses suggested activities to turn reservoir evidence into a controlled simulation workflow and a reviewable forecast.

Suggested activity: screen a static model, fluid description, rock-flow tables, contacts, and production history for simulation readiness.
Suggested activity: locate initialization, convergence, material-balance, and well-control problems from run messages and diagnostic plots.
Suggested activity: propose physically plausible changes for pressure, rate, water-cut, and gas-oil-ratio mismatches.
Suggested activity: compare development scenarios and communicate forecast assumptions, limitations, sensitivities, and actions.

FAQs

Who suits dynamic oil and gas reservoir simulation training, and what does it assume?

Dynamic oil and gas reservoir simulation training suits reservoir, simulation, subsurface, production, petroleum-engineering, and asset functions. It assumes practical familiarity with reservoir properties, well data, production history, and engineering calculations.

How does dynamic reservoir simulation differ from static reservoir modeling?

Static reservoir modeling describes geometry and spatial rock properties. Dynamic reservoir simulation adds fluid behavior, rock-flow functions, pressure and saturation conditions, wells, controls, time, and governing flow equations to predict reservoir response.

What inputs are required to initialize a reservoir simulation model?

Initialization normally requires a grid, pore-volume properties, regions, contacts, pressure datum, fluid properties, rock-flow functions, compressibility, saturation rules, aquifer or boundary assumptions, and volume checks that reconcile the model with geological and engineering evidence.

Why do reservoir simulation runs fail to converge?

Convergence problems can arise from inconsistent inputs, abrupt control changes, unsuitable timesteps, difficult phase behavior, sharp saturation changes, grid quality, well constraints, or solver settings. Diagnosis should preserve physical meaning rather than merely force a run to finish.

How is a reservoir simulation forecast quality-checked?

A forecast is checked through input lineage, initialization volumes, material balance, numerical stability, historical response, well behavior, constraint handling, scenario consistency, sensitivity to key assumptions, and clear documentation of limitations.

Conclusion

Participants take back a Reservoir Simulation Study File containing scope, data lineage, grid and property controls, initialization evidence, well and schedule definitions, run diagnostics, foundational calibration, forecast scenarios, quality checks, limitations, and actions. The file connects model construction to a traceable engineering review. It supports clearer simulation challenge and more defensible field-development decisions.

credits: 5 credit per day

Course Mode: full-time

Provider: Agile Leaders Training Center

Download Brochure (PDF) Print PDF

Showing 1-20 of 58 events

Location	Dates	Duration	Mode	Price
Geneva	Week 46, 2026 15 – 19 November 2026	1 Week	Onsite	€8,000
Abu Dhabi	Week 47, 2026 16 – 20 November 2026	1 Week	Onsite	€6,500
London	Week 51, 2026 14 – 18 December 2026	1 Week	Onsite	€6,500
Montreux	Week 51, 2026 14 – 18 December 2026	1 Week	Onsite	€8,000
Vienna	Week 52, 2026 21 – 25 December 2026	1 Week	Onsite	€7,500
Amman	Week 52, 2026 27 – 31 December 2026	1 Week	Onsite	€6,000
Casablanca	Week 01, 2027 4 – 8 January 2027	1 Week	Onsite	€6,000
Trabzon	Week 01, 2027 10 – 14 January 2027	1 Week	Onsite	€8,000
Toronto	Week 02, 2027 17 – 21 January 2027	1 Week	Onsite	€16,000
Dubai	Week 03, 2027 18 – 22 January 2027	1 Week	Onsite	€6,500
Sharm El-Sheikh	Week 04, 2027 25 – 29 January 2027	1 Week	Onsite	€5,200
Athens	Week 04, 2027 25 – 29 January 2027	1 Week	Onsite	€7,500
Baku	Week 06, 2027 8 – 12 February 2027	1 Week	Onsite	€8,000
Berlin	Week 06, 2027 8 – 12 February 2027	1 Week	Onsite	€6,500
Nairobi	Week 06, 2027 14 – 18 February 2027	1 Week	Onsite	€6,000
Barcelona	Week 08, 2027 22 – 26 February 2027	1 Week	Onsite	€6,500
Bangkok	Week 08, 2027 28 February – 4 March 2027	1 Week	Onsite	€8,000
Abu Dhabi	Week 09, 2027 1 – 5 March 2027	1 Week	Onsite	€6,500
Phuket	Week 10, 2027 14 – 18 March 2027	1 Week	Onsite	€8,000
London	Week 12, 2027 22 – 26 March 2027	1 Week	Onsite	€6,500

Frequently asked questions

What does this course cover?

OverviewDynamic Oil and Gas Reservoir Simulation Training Course is a one-week intermediate course for reservoir, simulation, subsurface, production, petroleum-engineering, and asset functions who leave with a Reservoir Simulation Study File. Participants convert static earth models and engineering data into initialized dynamic models, represent wells and…

Are training dates available?

Yes. Available dates and destinations are listed in the course dates section on this page.

How can I register?

Choose an available date on this page and complete the registration form, or send a programme enquiry.

Can I download the course brochure?

Yes. Use the brochure download link provided on this page.

Dynamic Reservoir Simulation Training Course