Torque and Drag Analysis for Drilling Course

Name: Torque and Drag Analysis for Drilling Operations Training Course
Availability: InStock

Build, calibrate, and interpret software-neutral load models for safer well planning and drilling decisions.

Torque and Drag Analysis for Drilling Course

At a glance

Duration: 1 Week
Format: Classroom
Cities: Paris, Tokyo, Singapore, Porto, Accra, Frankfurt and more
Next session: 9 – 13 November 2026, Paris
Average fee: 7,500 €

Home
Our Categories
Torque and Drag Analysis for Drilling Operations Training Course

Overview

Torque and Drag Analysis for Drilling Operations Training Course is a one-week course for drilling engineers, well planners, directional specialists, and operations teams who leave with a Torque and Drag Planning and Operations Decision Pack. Participants connect drillstring mechanics, friction and contact forces, well trajectory, load modelling, field calibration, operating limits, sensitivity analysis, and operational surveillance. Agile Leaders Training Center presents this course on torque and drag analysis for drilling operations.

Who Should Attend

Functions responsible for well trajectory and drillstring planning
Teams responsible for directional drilling and extended-reach feasibility
Personnel responsible for drilling load surveillance and performance analysis
Groups responsible for tubular selection and mechanical operating limits
Technical assurance teams responsible for drilling risk and decision review

The course assumes participants interpret well plans, drillstring data, and drilling measurements at work; it leaves out software-specific operation and detailed hydraulics design.

Departments and Industries

The course supports departments and industries that plan, execute, assure, or advise drilling and tubular operations.

Oil and gas drilling and well engineering departments
Directional drilling and well planning service teams
Rig operations and drilling performance functions
Tubular, casing, and completion engineering groups
Geothermal and subsurface construction projects
Engineering consultancy and technical assurance organizations

Learning Objectives

By the end of this course, participants will be able to:

Analyze friction, contact force, and trajectory effects
Build software-neutral torque and drag model inputs
Calibrate model outputs against measured drilling loads
Evaluate buckling, hookload, torque, and reach limits
Diagnose operational changes from load surveillance
Compare sensitivities and prioritize drilling risk controls

Course Agenda

Day 1: Frame Drillstring Load Mechanics

Axial and Torsional Load Path Diagram
Wellbore Contact and Normal-Force Model
Coulomb Friction Assumption Map
Soft-String and Stiff-String Comparison Matrix
Torque and Drag Analysis Boundary Register

Day 2: Build the Load Model

Survey and Well-Trajectory Input Checklist
Drillstring Component and Property Schedule
Buoyancy and Fluid-Effect Calculation Sheet
Cased-Hole and Open-Hole Friction Factor Table
Model Input Quality and Uncertainty Log

Day 3: Calibrate Operational Load Cases

Pickup and Slack-Off Hookload Envelope
Rotating and Sliding Torque Profile
Off-Bottom Load Calibration Workflow
Tripping and Backreaming Scenario Matrix
Measured-versus-Modelled Load Diagnostic Plot

Day 4: Test Limits and Operational Decisions

Sinusoidal and Helical Buckling Limit Chart
Weight-Transfer and Lock-Up Assessment
Rig and Tubular Operating Limit Overlay
Trajectory and Friction Sensitivity Analysis
Torque and Drag Surveillance Response Matrix

Day 5: Practice Torque and Drag Decisions

Suggested Exercise: Validate Model Input Quality
Suggested Exercise: Calibrate Field Friction Factors
Suggested Exercise: Diagnose a Load Trend Deviation
Suggested Exercise: Compare Reach and Operating Margins
Capstone Exercise: Present a Torque and Drag Planning and Operations Decision Pack

Practical Exercises

The course uses suggested activities to turn trajectory, string, fluid, friction, and measured-load evidence into drilling decisions.

Suggested activity: assemble a model input register and flag uncertain survey, string, hole, and fluid data.
Suggested activity: calibrate cased-hole and open-hole friction factors against pickup, slack-off, rotating, and off-bottom measurements.
Suggested activity: diagnose hole-condition changes using modeled-versus-measured hookload and torque trends.
Suggested activity: compare trajectory, friction, string, buckling, reach, and rig-limit sensitivities before selecting risk controls.

FAQs

Who suits torque and drag analysis for drilling operations training, and what does it assume?

Well planning, drilling, directional, performance, tubular, and technical assurance functions suit the training. It assumes experience interpreting well plans, drillstring data, and drilling measurements.

How does torque and drag analysis training differ from general drillstring design training?

Torque and drag analysis concentrates on friction, contact, trajectory, load modelling, calibration, buckling, limits, and operational surveillance. General drillstring design also addresses component selection, strength, fatigue, connections, and broader assembly design.

How are torque and drag models calibrated during drilling operations?

Models are calibrated by checking input quality, comparing calculated and measured pickup, slack-off, rotating, hookload, and torque values, separating cased-hole and open-hole effects, adjusting supported assumptions, and validating the result against additional measurements.

What causes torque and drag to increase in directional wells?

Torque and drag increase with trajectory curvature, inclination, contact force, friction, tortuosity, hole condition, cuttings accumulation, string configuration, fluid effects, and operating mode. The evidence must be tested together before a cause is assigned.

How should torque and drag operating limits support drilling decisions?

Operating limits should combine modeled loads, measured trends, buckling thresholds, tubular ratings, rig capability, uncertainty, and contingency margins so teams can compare options and escalate deviations consistently.

Conclusion

Participants take a Torque and Drag Planning and Operations Decision Pack back to their organization. It connects model inputs, calibration evidence, load envelopes, buckling limits, sensitivities, surveillance, and response choices. Teams can use the pack to document assumptions, test operating margins, identify deviations, and communicate drilling recommendations.

credits: 5 credit per day

Course Mode: full-time

Provider: Agile Leaders Training Center

Download Brochure (PDF) Print PDF

Showing 41-58 of 58 events

Location	Dates	Duration	Mode	Price
Bangkok	Week 27, 2027 11 – 15 July 2027	1 Week	Onsite	€8,000
Geneva	Week 28, 2027 18 – 22 July 2027	1 Week	Onsite	€8,000
New York	Week 30, 2027 26 – 30 July 2027	1 Week	Onsite	€16,000
Doha	Week 30, 2027 1 – 5 August 2027	1 Week	Onsite	€7,000
Madrid	Week 32, 2027 9 – 13 August 2027	1 Week	Onsite	€6,500
Zanzibar	Week 32, 2027 15 – 19 August 2027	1 Week	Onsite	€6,000
Seoul	Week 34, 2027 23 – 27 August 2027	1 Week	Onsite	€12,000
Toronto	Week 34, 2027 29 August – 2 September 2027	1 Week	Onsite	€16,000
Langkawi	Week 35, 2027 5 – 9 September 2027	1 Week	Onsite	€8,000
Vienna	Week 37, 2027 13 – 17 September 2027	1 Week	Onsite	€7,500
Trabzon	Week 37, 2027 19 – 23 September 2027	1 Week	Onsite	€8,000
Abu Dhabi	Week 39, 2027 27 September – 1 October 2027	1 Week	Onsite	€6,500
Amsterdam	Week 40, 2027 4 – 8 October 2027	1 Week	Onsite	€6,500
Lisbon	Week 41, 2027 11 – 15 October 2027	1 Week	Onsite	€6,500
Nairobi	Week 41, 2027 17 – 21 October 2027	1 Week	Onsite	€6,000
Munich	Week 43, 2027 25 – 29 October 2027	1 Week	Onsite	€6,500
Barcelona	Week 44, 2027 1 – 5 November 2027	1 Week	Onsite	€6,500
San Diego	Week 45, 2027 8 – 12 November 2027	1 Week	Onsite	€16,000

Frequently asked questions

What does this course cover?

OverviewTorque and Drag Analysis for Drilling Operations Training Course is a one-week course for drilling engineers, well planners, directional specialists, and operations teams who leave with a Torque and Drag Planning and Operations Decision Pack. Participants connect drillstring mechanics, friction and contact forces, well trajectory, load modelling,…

Are training dates available?

Yes. Available dates and destinations are listed in the course dates section on this page.

How can I register?

Choose an available date on this page and complete the registration form, or send a programme enquiry.

Can I download the course brochure?

Yes. Use the brochure download link provided on this page.

Torque and Drag Analysis for Drilling Course